Flexispot Vici Ec9 – 77% OFF Today Only

Flexispot Standing Desk Review …Flexispot Vici Ec9…

Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of features that I wasn’t necessarily a huge fan of:

The package that the desk came in was heavy, so bringing it inside was a group effort, however this is just a repercussion of how tough the Flexispot is.
The hassle-free cable tray was a bit complicated to set up. In the end, you eventually slip it under screws, which wasn’t very clear from the directions.
You will need to buy an anti-fatigue mat to remain comfortable, but this is a good concept for any standing desks, so I can’t fault Flexispot for that.

When it showed up and I saw how heavy it was, I was both excited (because this suggested it was going to be strong) and also a little reluctant (due to the fact that we all know how much of an obstacle assembling furniture can be).

Fortunately, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I discovered wasn’t explained well in the guidelines.

Once put together, I like the sleek look of this desk. I’m confident any of the many diverse finishes that it can be found in would look fantastic in any office, and the adjustable width makes it easy to fit it in even the smallest of office.

The peaceful operation and height memory settings make it easy, efficient, and quiet to change in between sitting and standing as many times as you desire throughout the day.

This desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a significant desktop (or want to rest on it for some reason) it has you covered. It will likewise evenly disperse weight no matter how unbalanced the weight you place on it is, it will not wiggle or wobble.

 

in that video is pretty kitted out as the desk we’re looking at today is pretty basic I attempted to get as close to that as I could on uplifts website with similar configurations the flexi spot desk we’re taking a look at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is actually five inches longer but you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for review but as you should understand by now does not impact my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering till completion of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can possibly get doing not have even any cable grommets for travel through the outdoors container

for the desktop was not damaged in any way which is entirely bizarre due to the fact that I might shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted simply extremely rough male if I had actually acquired this I ‘d have been on the phone with customer service immediately they did likewise handled to miss out on drilling the pilot holes where you can attach the control box to the desktop a lot of needing to do that myself without unintentionally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really pretty uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cable televisions running to it from each part to support motorized function strangely absolutely where any sort of cable television management materials whatsoever the frame on this unit is a single motor dual phase design versus the double motor three-stage design that comes standard with the uplift desk this can be upgraded also to both the dual stage double motor and a three-stage double motor which presses the expense of the desk up

an additional 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from simply under 28 inches to just over forty seven point six inches so a max I ‘d it is more than tall sufficient even for me and I remain at 6 foot for this design does come standard with the control panel that allows for up-and-down movement plus three memory areas with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which needs to be changed as the width of the desk is adjusted the motor operation itself while it might be slow is very peaceful as in barely audible this outside a cost would be the one benefit I would provide this unit over the uplift desk and I wish to beware here due to the fact that this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift design over 35% more affordable even if you upgrade this flexi area test to the double motor three-stage design it still comes in a hundred and seventy dollars cheaper than the uplift but less expensive doesn’t suggest cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll absolutely offer it that but the lateral stability of this desk the horizontal motion at this price point it’s unacceptable it’s add insult to injury here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a part of this rotating driveshaft when

this desk sees any lateral motion at all the drive shaft hits the sound and this baffle is definitely frustrating to top things off I decided to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters arrived harmed too my plan for this desk at this point is to lose the desk top and featured entirely and replace it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops as much as 63 inches wide and 31 and a half inches deep so this will roll around the studio make it much easier to movie items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is an investment in quality workplace furnishings that will last you this at best seems like a cheaper imitation of that it simply doesn’t feel quality and the distinction in between this desk and my main desk is night and day do do not hesitate to take a look at their website also which likewise feels strangely similar to among their competitors there’s a wealth of devices you can get for the flexi area desk approximately and consisting of a foot massager and even a stationary exercise bike and I might invest another 10 minutes of our valuable time covering various alternatives and accessories I could however I think I’m happier that they just sent a basic desk since as a fundamental desk I’m not a fan of the quality control at this cost point and I do not think slapping on a bunch of bonus is the move when the core product isn’t what it ought to be they do provide a 30-day trial if you’re simply morbidly curious and they guarantee their desks for three years really desk is five years and uplift desk is 7 years if you are Flexispot Vici Ec9

in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in regards to video gaming and performance but I would invest the extra money it’s gon na take to enter into a higher end maker like uplift desk or very desk and I have not personally utilized very desk items so I can’t speak on it but their credibility is very good big thanks to flexi area for sending this out for review unfortunately I can not suggest this system and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with seeing as how both the desktop and the casters showed up harmed but from a client standpoint you ‘d probably be really excited to get this in