Flexispot Standing Desk Review …Flexispot V9U…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a couple of features that I wasn’t always a big fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how strong the Flexispot is.
The hassle-free cable tray was a bit complicated to set up. In the end, you eventually slip it under screws, which wasn’t very clear from the directions.
You will require to buy an anti-fatigue mat to stay comfy, however this is a great concept for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both excited (given that this indicated it was going to be durable) and also a little hesitant (since all of us understand how much of a challenge putting together furnishings can be).
Fortunately, with the help of a training YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I found wasn’t described well in the guidelines.
Once put together, I love the smooth appearance of this desk. I’m positive any of the many diverse finishes that it can be found in would look great in any office, and the adjustable width makes it simple to fit it in even the smallest of home offices.
The peaceful operation and height memory settings make it simple, effective, and quiet to change in between sitting and standing as sometimes as you desire throughout the day.
This desk is durable. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop computer (or want to take a nap on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how out of balance the weight you put on it is, it will not wiggle or wobble.
because video is pretty kitted out as the desk we’re looking at today is quite standard I attempted to get as near that as I could on uplifts site with comparable setups the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus six hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift design is in fact 5 inches longer however you can do a lot with 5 inches boom yes now for transparency flexi spot did send this desk out for review but as you should understand by now does not impact my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering up until completion of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can perhaps get doing not have even any cable television grommets for travel through the outside carton
for the desktop was not damaged in any way which is absolutely bizarre because I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted just very rough guy if I had actually purchased this I ‘d have been on the phone with customer support instantly they did also handled to miss drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without unintentionally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was actually pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function unusually definitely where any sort of cable management materials whatsoever the frame on this unit is a single motor dual phase design versus the double motor three-stage design that comes requirement with the uplift desk this can be updated also to both the double stage double motor and a three-stage dual motor which pushes the expense of the desk up
an additional 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from simply under 28 inches to simply over forty 7 point 6 inches so a max I ‘d it is more than tall sufficient even for me and I remain at 6 foot for this model does come standard with the control panel that enables up-and-down movement plus 3 memory areas with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be sluggish is extremely peaceful as in barely audible this outside a rate would be the one benefit I would offer this unit over the uplift desk and I wish to beware here since this isn’t a hit piece this desk is 240 dollars cheaper than the comparable uplift model over 35% more affordable even if you upgrade this flexi area test to the double motor three-stage design it still is available in a hundred and seventy dollars more affordable than the uplift but cheaper does not suggest low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll definitely provide it that however the lateral stability of this desk the horizontal motion at this cost point it’s unacceptable it’s add insult to injury here they include a little security baffle this little steel piece that installs to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft strikes this baffle and the sound is definitely frustrating to leading things off I chose to add rolling casters to this desk this was a $30 upgrade and two of those 4 casters arrived damaged as well my prepare for this desk at this point is to lose the desk top and featured completely and change it with a white laminate lemon table from Ikea and use it as an adjustable image table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it easier to film items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is a financial investment in quality office furnishings that will last you this at best feels like a cheaper replica of that it simply does not feel quality and the distinction in between this desk and my primary desk is night and day do feel free to check out their site as well which also feels strangely comparable to one of their competitors there’s a wealth of devices you can get for the flexi area desk approximately and including a foot massager and even a fixed stationary bicycle and I might spend another 10 minutes of our precious time covering various alternatives and accessories I could but I believe I’m happier that they just sent out a fundamental desk due to the fact that as a basic desk I’m not a fan of the quality control at this rate point and I don’t believe slapping on a lot of additionals is the move when the core product isn’t what it should be they do provide a 30-day trial if you’re just morbidly curious and they warranty their desks for 3 years very desk is five years and uplift desk is seven years if you are Flexispot V9U
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in terms of video gaming and productivity but I would spend the money it’s gon na take to get into a greater end producer like uplift desk or extremely desk and I have not personally used extremely desk products so I can’t speak on it but their track record is great huge thanks to flexi spot for sending this out for evaluation regrettably I can not suggest this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a problem with seeing as how both the desktop and the casters showed up harmed however from a customer viewpoint you ‘d probably be actually excited to get this in