Flexispot V9 – 77% OFF Today Only

Flexispot Standing Desk Evaluation …Flexispot V9…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a couple of functions that I wasn’t necessarily a big fan of:

The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is just a consequence of how durable the Flexispot is.
The practical cable tray was a little bit confusing to install. In the end, you eventually slip it under screws, which wasn’t very clear from the instructions.
You will require to buy an anti-fatigue mat to remain comfortable, however this is a great idea for any standing desks, so I can’t fault Flexispot for that.

When it arrived and I saw how heavy it was, I was both ecstatic (because this implied it was going to be sturdy) and also a little hesitant (because we all understand how much of an obstacle assembling furnishings can be).

Fortunately, with the help of a training YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only problem I have with assembly was the cable television tray, which I found wasn’t discussed well in the directions.

Once assembled, I like the smooth look of this desk. I’m confident any of the many varied surfaces that it is available in would look excellent in any office, and the adjustable width makes it easy to fit it in even the tiniest of home offices.

The quiet operation and height memory settings make it easy, efficient, and peaceful to switch between sitting and standing as often times as you desire throughout the day.

Last but not least, this desk is strong. It can hold up to 335 lbs even while in operation, so if you have a large desktop computer (or want to rest on it for some reason) it has you covered. It will also uniformly disperse weight no matter how out of balance the weight you place on it is, it won’t wiggle or wobble.

 

because video is pretty kitted out as the desk we’re looking at today is pretty standard I attempted to get as near to that as I might on uplifts website with equivalent setups the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift design is in fact five inches longer but you can do a lot with 5 inches boom yes now for transparency flexi spot did send this desk out for review but as you need to know by now does not affect my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping until the end of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can perhaps get lacking even any cable grommets for travel through the outdoors carton

for the desktop was not harmed in any way which is entirely bizarre because I could shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted simply extremely rough guy if I had actually purchased this I ‘d have been on the phone with customer service instantly they did also managed to miss drilling the pilot holes where you can attach the control box to the desktop a lot of having to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really quite simple the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each element to support motorized function strangely absolutely where any kind of cable television management materials whatsoever the frame on this unit is a single motor double phase design versus the dual motor three-stage style that comes standard with the uplift desk this can be updated also to both the double stage double motor and a three-stage dual motor which pushes the cost of the desk up

an additional 70 dollars the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to just over forty seven point six inches so a max I ‘d it is more than high sufficient even for me and I stay at 6 foot for this model does come standard with the control board that enables up-and-down movement plus 3 memory areas with an LED readout to inform you the desk height the single motor style utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is very peaceful as in barely audible this outside a cost would be the one benefit I would provide this system over the uplift desk and I want to beware here because this isn’t a hit piece this desk is 240 dollars cheaper than the equivalent uplift model over 35% less expensive even if you update this flexi area test to the dual motor three-stage style it still can be found in a hundred and seventy dollars cheaper than the uplift however cheaper does not mean cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely give it that however the lateral stability of this desk the horizontal motion at this price point it’s undesirable it’s add insult to injury here they include a little safety baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when

this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is definitely frustrating to top things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters showed up damaged also my prepare for this desk at this moment is to lose the desk top and came with completely and change it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to movie products without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality office furniture that will last you this at finest seems like a cheaper replica of that it simply does not feel quality and the distinction between this desk and my main desk is night and day do do not hesitate to check out their website also which also feels strangely comparable to one of their competitors there’s a wealth of devices you can get for the flexi area desk up to and consisting of a foot massager and even a fixed stationary bicycle and I might invest another 10 minutes of our precious time covering different options and accessories I could but I think I’m happier that they just sent out a fundamental desk because as a fundamental desk I’m not a fan of the quality control at this cost point and I do not think slapping on a bunch of additionals is the relocation when the core item isn’t what it should be they do provide a 30-day trial if you’re just morbidly curious and they service warranty their desks for three years extremely desk is five years and uplift desk is seven years if you are Flexispot V9

in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to video gaming and productivity but I would invest the money it’s gon na take to enter into a higher end manufacturer like uplift desk or extremely desk and I haven’t personally used really desk products so I can’t speak on it however their reputation is very good huge thanks to flexi spot for sending this out for evaluation unfortunately I can not advise this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with seeing as how both the desktop and the casters arrived damaged but from a client perspective you ‘d most likely be really delighted to get this in