Flexispot Standing Desk Review …Flexispot Under Desk Drawer…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a couple of functions that I wasn’t necessarily a big fan of:
The package that the desk can be found in was heavy, so bringing it inside was a group effort, but this is just an effect of how tough the Flexispot is.
The convenient cable tray was a bit complicated to install. In the end, you eventually slip it under screws, which wasn’t extremely clear from the instructions.
You will need to buy an anti-fatigue mat to stay comfy, but this is a great concept for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both fired up (considering that this implied it was going to be sturdy) and also a little reluctant (because we all understand how much of a challenge putting together furnishings can be).
Luckily, with the help of an educational YouTube link, it took me only around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable television tray, which I found wasn’t discussed well in the guidelines.
As soon as put together, I like the smooth appearance of this desk. I’m confident any of the many varied finishes that it comes in would look excellent in any office, and the adjustable width makes it simple to fit it in even the smallest of office.
The quiet operation and height memory settings make it easy, efficient, and peaceful to change between sitting and standing as sometimes as you desire throughout the day.
This desk is strong. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop (or want to rest on it for some reason) it has you covered. It will also uniformly disperse weight no matter how unbalanced the weight you put on it is, it will not wobble or wiggle.
because video is quite kitted out as the desk we’re taking a look at today is pretty standard I tried to get as near to that as I might on uplifts site with comparable configurations the flexi area desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is in fact five inches longer but you can do a lot with five inches boom yes now for transparency flexi spot did send this desk out for evaluation however as you ought to understand by now does not affect my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping until completion of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can possibly get lacking even any cable television grommets for pass through the outside container
for the desktop was not damaged in any way which is utterly unusual since I could shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just extremely rough guy if I had purchased this I ‘d have been on the phone with customer support instantly they did also handled to miss drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was in fact pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each part to support motorized function oddly absolutely where any kind of cable television management products whatsoever the frame on this system is a single motor double phase style versus the dual motor three-stage style that comes requirement with the uplift desk this can be upgraded too to both the double phase double motor and a three-stage dual motor which presses the cost of the desk up
an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from simply under 28 inches to simply over forty 7 point six inches so a max I ‘d it is more than tall adequate even for me and I remain at 6 foot for this design does come standard with the control panel that allows for up-and-down motion plus 3 memory spots with an LED readout to inform you the desk height the single motor design utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is very peaceful as in barely audible this outside a rate would be the one advantage I would offer this system over the uplift desk and I wish to beware here due to the fact that this isn’t a hit piece this desk is 240 dollars more affordable than the similar uplift model over 35% less expensive even if you update this flexi spot test to the dual motor three-stage style it still can be found in a hundred and seventy dollars more affordable than the uplift however cheaper doesn’t mean low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely provide it that but the lateral stability of this desk the horizontal movement at this price point it’s inappropriate it’s add fuel to the fire here they consist of a little security baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is definitely frustrating to top things off I decided to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters arrived harmed too my plan for this desk at this point is to lose the desk top and included all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops up to 63 inches large and 31 and a half inches deep so this will roll around the studio make it much easier to film items without needing to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality office furniture that will last you this at finest feels like a more affordable replica of that it simply doesn’t feel quality and the distinction between this desk and my primary desk is night and day do feel free to have a look at their site too which likewise feels eerily similar to among their rivals there’s a wealth of accessories you can get for the flexi spot desk up to and including a foot massager and even a stationary stationary bicycle and I could invest another 10 minutes of our valuable time covering numerous options and accessories I might but I believe I’m happier that they only sent out a fundamental desk since as a basic desk I’m not a fan of the quality control at this price point and I don’t think slapping on a lot of extras is the move when the core item isn’t what it need to be they do provide a 30-day trial if you’re just morbidly curious and they warranty their desks for three years really desk is 5 years and uplift desk is 7 years if you are Flexispot Under Desk Drawer
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in regards to video gaming and productivity but I would spend the additional money it’s gon na require to get into a higher end producer like uplift desk or extremely desk and I have not personally utilized really desk items so I can’t speak on it however their credibility is excellent huge thanks to flexi area for sending this out for evaluation regrettably I can not recommend this system and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had an issue with viewing as how both the desktop and the casters showed up harmed however from a customer viewpoint you ‘d most likely be truly thrilled to get this in