Flexispot Standing Desk Motor – 77% OFF Today Only

Flexispot Standing Desk Evaluation …Flexispot Standing Desk Motor…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of features that I wasn’t necessarily a big fan of:

The bundle that the desk can be found in was heavy, so bringing it inside was a group effort, but this is simply a consequence of how durable the Flexispot is.
The practical cable tray was a little bit complicated to set up. In the end, you ultimately slip it under screws, which wasn’t really clear from the guidelines.
You will require to buy an anti-fatigue mat to stay comfortable, however this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.

When it arrived and I saw how heavy it was, I was both excited (since this meant it was going to be durable) and also a little hesitant (since we all know how much of a challenge putting together furnishings can be).

Luckily, with the help of an instructional YouTube link, it took me only around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t explained well in the guidelines.

Once put together, I love the smooth look of this desk. I’m confident any of the many diverse finishes that it can be found in would look great in any office, and the adjustable width makes it simple to fit it in even the smallest of office.

The quiet operation and height memory settings make it simple, effective, and quiet to change between sitting and standing as often times as you desire throughout the day.

This desk is durable. It can hold up to 335 lbs even while in operation, so if you have a hefty desktop computer (or want to sleep on it for some reason) it has you covered. It will likewise evenly distribute weight no matter how unbalanced the weight you place on it is, it will not wobble or wiggle.

 

because video is pretty kitted out as the desk we’re looking at today is quite basic I tried to get as near to that as I could on uplifts site with similar setups the flexi spot desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is in fact 5 inches longer however you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for evaluation but as you need to understand by now doesn’t impact my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering up until completion of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can potentially get doing not have even any cable grommets for pass through the outside carton

for the desktop was not damaged in any way which is absolutely strange since I could shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted just super rough man if I had actually acquired this I ‘d have been on the phone with customer care instantly they did likewise handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was in fact quite straightforward the whole thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function strangely absolutely where any sort of cable management materials whatsoever the frame on this system is a single motor dual stage style versus the dual motor three-stage design that comes standard with the uplift desk this can be upgraded as well to both the dual stage dual motor and a three-stage dual motor which pushes the cost of the desk up

an additional 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than tall adequate even for me and I remain at 6 foot for this design does come basic with the control panel that permits up-and-down movement plus three memory spots with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be slow is extremely peaceful as in barely audible this outside a cost would be the one advantage I would offer this system over the uplift desk and I wish to be careful here since this isn’t a hit piece this desk is 240 dollars cheaper than the equivalent uplift design over 35% less expensive even if you upgrade this flexi area test to the double motor three-stage design it still can be found in a hundred and seventy dollars more affordable than the uplift but less expensive doesn’t imply low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll absolutely provide it that but the lateral stability of this desk the horizontal movement at this cost point it’s undesirable it’s add fuel to the fire here they include a little security baffle this little steel piece that installs to the frame and covers a part of this turning driveshaft when

this desk sees any lateral movement at all the drive shaft strikes this baffle and the sound is absolutely infuriating to leading things off I decided to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters arrived harmed too my plan for this desk at this moment is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches broad and 31 and a half inches deep so this will roll around the studio make it much easier to film items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift initially that is a financial investment in quality workplace furnishings that will last you this at best feels like a less expensive imitation of that it just does not feel quality and the difference between this desk and my main desk is night and day do do not hesitate to take a look at their site also which also feels strangely similar to one of their rivals there’s a wealth of accessories you can get for the flexi spot desk approximately and consisting of a foot massager and even a stationary exercise bike and I might invest another 10 minutes of our precious time covering different choices and devices I could but I believe I’m better that they just sent out a fundamental desk due to the fact that as a basic desk I’m not a fan of the quality assurance at this cost point and I do not believe slapping on a lot of additionals is the relocation when the core item isn’t what it should be they do use a 30-day trial if you’re just morbidly curious and they guarantee their desks for 3 years extremely desk is five years and uplift desk is seven years if you are Flexispot Standing Desk Motor

in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in terms of gaming and performance however I would spend the money it’s gon na take to enter a higher end maker like uplift desk or very desk and I have not personally used really desk items so I can’t speak on it but their reputation is great huge thanks to flexi spot for sending this out for evaluation unfortunately I can not recommend this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a problem with viewing as how both the desktop and the casters arrived harmed but from a customer viewpoint you ‘d most likely be truly excited to get this in