Flexispot Standing Desk E7 – 77% OFF Today Only

Flexispot Standing Desk Review …Flexispot Standing Desk E7…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a few features that I wasn’t always a huge fan of:

The package that the desk was available in was heavy, so bringing it inside was a group effort, but this is just an effect of how tough the Flexispot is.
The convenient cable television tray was a bit confusing to install. In the end, you ultimately slip it under screws, which wasn’t really clear from the guidelines.
You will need to buy an anti-fatigue mat to remain comfortable, however this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.

When it arrived and I saw how heavy it was, I was both thrilled (because this implied it was going to be tough) and also a little reluctant (because we all know just how much of a challenge assembling furniture can be).

Fortunately, with the help of an educational YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I found wasn’t discussed well in the directions.

As soon as assembled, I love the sleek look of this desk. I’m positive any of the many diverse surfaces that it can be found in would look fantastic in any office, and the adjustable width makes it easy to fit it in even the smallest of office.

The quiet operation and height memory settings make it easy, effective, and quiet to change between sitting and standing as often times as you want throughout the day.

Finally, this desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop (or wish to rest on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how out of balance the weight you place on it is, it will not wiggle or wobble.

 

in that video is quite kitted out as the desk we’re taking a look at today is quite standard I attempted to get as near that as I might on uplifts site with similar configurations the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift model is in fact five inches longer however you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for review but as you should know by now doesn’t affect my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering until the end of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can possibly get lacking even any cable grommets for travel through the outdoors container

for the desktop was not damaged in any way which is utterly unusual due to the fact that I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted simply super rough male if I had bought this I ‘d have been on the phone with customer service right away they did also handled to miss drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without inadvertently drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each element to support motorized function strangely absolutely where any sort of cable television management products whatsoever the frame on this unit is a single motor dual phase style versus the double motor three-stage style that comes requirement with the uplift desk this can be updated also to both the dual phase dual motor and a three-stage double motor which pushes the cost of the desk up

an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to simply over forty seven point 6 inches so a max I ‘d it is more than tall enough even for me and I stay at 6 foot for this design does come basic with the control board that allows for up-and-down movement plus three memory areas with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be slow is really quiet as in barely audible this outside a price would be the one benefit I would offer this system over the uplift desk and I wish to take care here due to the fact that this isn’t a hit piece this desk is 240 dollars cheaper than the comparable uplift model over 35% cheaper even if you update this flexi spot test to the dual motor three-stage design it still is available in a hundred and seventy dollars more affordable than the uplift but less expensive does not imply low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely give it that but the lateral stability of this desk the horizontal movement at this price point it’s unacceptable it’s add fuel to the fire here they include a little security baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when

this desk sees any lateral motion at all the drive shaft strikes this baffle and the noise is definitely frustrating to leading things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those four casters arrived damaged as well my plan for this desk at this point is to lose the desk top and included entirely and replace it with a white laminate lemon table from Ikea and use it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches broad and 31 and a half inches deep so this will roll around the studio make it easier to film items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift initially that is an investment in quality office furnishings that will last you this at finest feels like a cheaper replica of that it simply does not feel quality and the distinction in between this desk and my main desk is night and day do do not hesitate to take a look at their website too which likewise feels eerily similar to among their rivals there’s a wealth of devices you can get for the flexi spot desk as much as and including a foot massager and even a stationary stationary bicycle and I might spend another 10 minutes of our precious time covering numerous alternatives and accessories I might but I think I’m happier that they only sent a basic desk because as a basic desk I’m not a fan of the quality control at this rate point and I do not believe slapping on a lot of bonus is the relocation when the core product isn’t what it must be they do provide a 30-day trial if you’re just morbidly curious and they warranty their desks for three years very desk is five years and uplift desk is seven years if you are Flexispot Standing Desk E7

in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in regards to gaming and efficiency however I would invest the money it’s gon na take to get into a higher end producer like uplift desk or very desk and I haven’t personally used extremely desk items so I can’t speak on it but their credibility is great huge thanks to flexi area for sending this out for evaluation unfortunately I can not advise this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with seeing as how both the desktop and the casters showed up harmed however from a client perspective you ‘d probably be really excited to get this in