Flexispot Sit2Go – 77% OFF Today Only

Flexispot Standing Desk Review …Flexispot Sit2Go…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of features that I wasn’t always a big fan of:

The plan that the desk can be found in was heavy, so bringing it inside was a group effort, however this is just an effect of how strong the Flexispot is.
The hassle-free cable tray was a little bit complicated to install. In the end, you eventually slip it under screws, which wasn’t really clear from the guidelines.
You will need to buy an anti-fatigue mat to remain comfortable, but this is a great idea for any standing desks, so I can’t fault Flexispot for that.

When it got here and I saw how heavy it was, I was both fired up (since this suggested it was going to be strong) and also a little hesitant (since we all understand how much of an obstacle putting together furniture can be).

The good news is, with the help of an instructional YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t discussed well in the directions.

As soon as assembled, I love the smooth look of this desk. I’m positive any of the many diverse surfaces that it can be found in would look fantastic in any workplace, and the adjustable width makes it easy to fit it in even the smallest of home offices.

The peaceful operation and height memory settings make it easy, efficient, and peaceful to change in between sitting and standing as sometimes as you desire throughout the day.

This desk is durable. It can hold up to 335 pounds even while in operation, so if you have a significant desktop computer (or wish to rest on it for some reason) it has you covered. It will also equally disperse weight no matter how out of balance the weight you put on it is, it won’t wiggle or wobble.

 

in that video is pretty kitted out as the desk we’re taking a look at today is quite standard I tried to get as near to that as I could on uplifts site with comparable setups the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift model is actually 5 inches longer however you can do a lot with five inches boom yes now for transparency flexi spot did send this desk out for evaluation but as you must understand by now does not affect my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering till completion of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can possibly get doing not have even any cable grommets for pass through the outside container

for the desktop was not harmed in any way which is entirely strange because I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted just extremely rough man if I had purchased this I ‘d have been on the phone with customer service immediately they did also managed to miss drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was actually quite uncomplicated the whole thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each part to support motorized function strangely definitely where any sort of cable management products whatsoever the frame on this unit is a single motor dual phase style versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded also to both the dual phase double motor and a three-stage dual motor which presses the cost of the desk up

an additional 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than tall enough even for me and I remain at 6 foot for this model does come basic with the control board that enables up-and-down movement plus 3 memory areas with an LED readout to inform you the desk height the single motor design uses this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is really peaceful as in barely audible this outside a cost would be the one benefit I would offer this unit over the uplift desk and I want to take care here because this isn’t a hit piece this desk is 240 dollars less expensive than the comparable uplift model over 35% more affordable even if you update this flexi spot test to the dual motor three-stage style it still can be found in a hundred and seventy dollars more affordable than the uplift but cheaper doesn’t imply low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll definitely provide it that but the lateral stability of this desk the horizontal motion at this rate point it’s undesirable it’s add fuel to the fire here they include a little security baffle this little steel piece that installs to the frame and covers a part of this turning driveshaft when

this desk sees any lateral movement at all the drive shaft hits the noise and this baffle is absolutely infuriating to leading things off I chose to add rolling casters to this desk this was a $30 upgrade and two of those four casters showed up damaged as well my prepare for this desk at this moment is to lose the desk top and came with completely and replace it with a white laminate lemon table from Ikea and use it as an adjustable image table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it easier to film products without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is an investment in quality office furniture that will last you this at best seems like a less expensive replica of that it simply doesn’t feel quality and the difference between this desk and my main desk is night and day do do not hesitate to check out their website too which also feels eerily comparable to among their competitors there’s a wealth of devices you can get for the flexi area desk as much as and consisting of a foot massager and even a stationary exercise bike and I might spend another 10 minutes of our valuable time covering various options and accessories I might however I think I’m happier that they only sent a basic desk because as a basic desk I’m not a fan of the quality assurance at this cost point and I do not believe slapping on a bunch of extras is the move when the core product isn’t what it need to be they do offer a 30-day trial if you’re just morbidly curious and they service warranty their desks for three years very desk is five years and uplift desk is 7 years if you are Flexispot Sit2Go

in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of gaming and efficiency however I would invest the money it’s gon na require to enter into a higher end maker like uplift desk or really desk and I have not personally used extremely desk items so I can’t speak on it but their track record is great big thanks to flexi area for sending this out for review unfortunately I can not suggest this unit and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a concern with seeing as how both the desktop and the casters showed up damaged but from a client perspective you ‘d probably be actually thrilled to get this in