Flexispot Standing Desk Review …Flexispot Return Policy…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a few features that I wasn’t necessarily a big fan of:
The bundle that the desk can be found in was heavy, so bringing it inside was a group effort, however this is simply a repercussion of how strong the Flexispot is.
The practical cable tray was a little bit complicated to set up. In the end, you eventually slip it under screws, which wasn’t really clear from the instructions.
You will need to buy an anti-fatigue mat to remain comfortable, however this is a good idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both ecstatic (considering that this indicated it was going to be sturdy) and also a little hesitant (since all of us understand just how much of an obstacle assembling furnishings can be).
Luckily, with the help of an instructional YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t explained well in the directions.
Once put together, I love the smooth appearance of this desk. I’m positive any of the many varied finishes that it can be found in would look excellent in any office, and the adjustable width makes it easy to fit it in even the smallest of home offices.
The quiet operation and height memory settings make it easy, effective, and quiet to switch in between sitting and standing as many times as you desire throughout the day.
Lastly, this desk is sturdy. It can hold up to 335 lbs even while in operation, so if you have a substantial desktop (or wish to rest on it for some reason) it has you covered. It will also equally disperse weight no matter how out of balance the weight you put on it is, it won’t wobble or wiggle.
in that video is quite kitted out as the desk we’re taking a look at today is quite fundamental I tried to get as near to that as I might on uplifts website with similar setups the flexi area desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift design is in fact 5 inches longer however you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for evaluation however as you must know by now doesn’t impact my review in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping up until the end of April at the earliest the desktop is an inch thick however it’s this standard laminate as you can perhaps get lacking even any cable television grommets for go through the outdoors container
for the desktop was not damaged in any way which is utterly unusual since I might shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just very rough man if I had bought this I ‘d have been on the phone with customer service instantly they did also managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of needing to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was in fact quite simple the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each component to support motorized function strangely definitely where any sort of cable television management products whatsoever the frame on this system is a single motor dual phase style versus the double motor three-stage design that comes standard with the uplift desk this can be upgraded also to both the double stage double motor and a three-stage double motor which presses the cost of the desk up
an extra 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to just over forty seven point 6 inches so a max I ‘d it is more than high enough even for me and I stay at 6 foot for this design does come basic with the control board that permits up-and-down movement plus three memory spots with an LED readout to tell you the desk height the single motor design utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is really quiet as in barely audible this outside a rate would be the one benefit I would give this system over the uplift desk and I wish to take care here due to the fact that this isn’t a hit piece this desk is 240 dollars less expensive than the comparable uplift model over 35% more affordable even if you update this flexi spot test to the dual motor three-stage style it still is available in a hundred and seventy dollars less expensive than the uplift but cheaper doesn’t suggest low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll certainly provide it that however the lateral stability of this desk the horizontal motion at this price point it’s inappropriate it’s rub salt in the wound here they consist of a little security baffle this little steel piece that installs to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft strikes the noise and this baffle is definitely shocking to top things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those 4 casters arrived harmed too my prepare for this desk at this point is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops up to 63 inches large and 31 and a half inches deep so this will roll around the studio make it simpler to film products without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is a financial investment in quality office furniture that will last you this at finest seems like a less expensive replica of that it just does not feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to have a look at their site as well which likewise feels strangely comparable to one of their rivals there’s a wealth of devices you can get for the flexi area desk approximately and including a foot massager and even a stationary exercise bike and I could spend another 10 minutes of our precious time covering numerous choices and devices I might however I believe I’m better that they just sent a fundamental desk since as a standard desk I’m not a fan of the quality assurance at this price point and I don’t think slapping on a lot of extras is the relocation when the core item isn’t what it need to be they do use a 30-day trial if you’re just morbidly curious and they guarantee their desks for 3 years very desk is 5 years and uplift desk is seven years if you are Flexispot Return Policy
in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in terms of gaming and performance but I would spend the extra money it’s gon na take to get into a higher end manufacturer like uplift desk or extremely desk and I haven’t personally utilized really desk products so I can’t speak on it however their track record is excellent huge thanks to flexi spot for sending this out for evaluation regrettably I can not recommend this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a problem with viewing as how both the desktop and the casters showed up harmed but from a client perspective you ‘d probably be actually thrilled to get this in