Flexispot Memory Controller – 77% OFF Today Only

Flexispot Standing Desk Review …Flexispot Memory Controller…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a few functions that I wasn’t always a huge fan of:

The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is just a consequence of how sturdy the Flexispot is.
The convenient cable tray was a bit complicated to install. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the directions.
You will need to purchase an anti-fatigue mat to remain comfy, but this is a good idea for any standing desks, so I can’t fault Flexispot for that.

When it got here and I saw how heavy it was, I was both ecstatic (since this suggested it was going to be sturdy) and also a little reluctant (because we all understand just how much of a difficulty putting together furnishings can be).

Thankfully, with the help of an instructional YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t explained well in the guidelines.

When put together, I enjoy the sleek appearance of this desk. I’m confident any of the many varied surfaces that it comes in would look excellent in any office, and the adjustable width makes it simple to fit it in even the tiniest of office.

The peaceful operation and height memory settings make it simple, efficient, and quiet to change in between sitting and standing as lot of times as you desire throughout the day.

This desk is tough. It can hold up to 335 pounds even while in operation, so if you have a hefty desktop computer (or wish to rest on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how unbalanced the weight you place on it is, it won’t wobble or wiggle.

 

because video is quite kitted out as the desk we’re taking a look at today is pretty basic I attempted to get as near to that as I might on uplifts website with equivalent setups the flexi area desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift model is really five inches longer but you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for evaluation but as you must understand by now does not impact my evaluation in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping until completion of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can perhaps get doing not have even any cable television grommets for pass through the outdoors carton

for the desktop was not harmed in any way which is entirely unusual since I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted just very rough guy if I had actually purchased this I ‘d have been on the phone with customer service instantly they did likewise managed to miss out on drilling the pilot holes where you can attach the control box to the desktop a great deal of needing to do that myself without mistakenly drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really pretty simple the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function strangely absolutely where any sort of cable management materials whatsoever the frame on this unit is a single motor double stage style versus the dual motor three-stage style that comes standard with the uplift desk this can be upgraded too to both the double stage dual motor and a three-stage dual motor which pushes the expense of the desk up

an additional 70 bucks the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to just over forty 7 point 6 inches so a max I ‘d it is more than high enough even for me and I stay at 6 foot for this model does come standard with the control board that allows for up-and-down movement plus three memory areas with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be sluggish is extremely peaceful as in barely audible this outside a rate would be the one benefit I would provide this system over the uplift desk and I want to take care here due to the fact that this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift design over 35% cheaper even if you update this flexi area test to the double motor three-stage design it still is available in a hundred and seventy dollars cheaper than the uplift but less expensive doesn’t imply inexpensive this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is strong even if max height I’ll definitely give it that however the lateral stability of this desk the horizontal motion at this cost point it’s unacceptable it’s add fuel to the fire here they include a little security baffle this little steel piece that mounts to the frame and covers a part of this turning driveshaft when

this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is definitely shocking to leading things off I decided to include rolling casters to this desk this was a $30 upgrade and 2 of those four casters arrived damaged also my plan for this desk at this point is to lose the desk top and featured completely and change it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it easier to film products without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furnishings that will last you this at finest seems like a cheaper replica of that it just does not feel quality and the distinction in between this desk and my primary desk is night and day do do not hesitate to have a look at their site also which also feels eerily comparable to among their rivals there’s a wealth of devices you can get for the flexi spot desk as much as and including a foot massager and even a stationary stationary bicycle and I might spend another 10 minutes of our valuable time covering different alternatives and accessories I might however I think I’m better that they just sent a basic desk because as a standard desk I’m not a fan of the quality control at this price point and I don’t believe slapping on a bunch of bonus is the move when the core item isn’t what it need to be they do offer a 30-day trial if you’re simply morbidly curious and they service warranty their desks for three years extremely desk is 5 years and uplift desk is seven years if you are Flexispot Memory Controller

in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of video gaming and efficiency however I would spend the extra money it’s gon na take to enter into a greater end manufacturer like uplift desk or very desk and I haven’t personally used really desk products so I can’t speak on it but their credibility is great big thanks to flexi spot for sending this out for evaluation unfortunately I can not recommend this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with viewing as how both the desktop and the casters showed up damaged but from a client perspective you ‘d most likely be truly excited to get this in