Flexispot Standing Desk Review …Flexispot Mahogany…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of features that I wasn’t always a huge fan of:
The plan that the desk can be found in was heavy, so bringing it inside was a group effort, however this is just a repercussion of how durable the Flexispot is.
The practical cable tray was a little bit complicated to install. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the directions.
You will need to buy an anti-fatigue mat to remain comfy, but this is a good concept for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both ecstatic (because this meant it was going to be sturdy) and likewise a little reluctant (due to the fact that all of us understand how much of a challenge putting together furnishings can be).
Fortunately, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t discussed well in the directions.
As soon as assembled, I enjoy the smooth look of this desk. I’m positive any of the many varied finishes that it is available in would look fantastic in any workplace, and the adjustable width makes it easy to fit it in even the tiniest of home offices.
The peaceful operation and height memory settings make it easy, efficient, and peaceful to switch between sitting and standing as often times as you desire throughout the day.
This desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a large desktop computer (or want to rest on it for some reason) it has you covered. It will likewise equally distribute weight no matter how unbalanced the weight you put on it is, it will not wiggle or wobble.
because video is quite kitted out as the desk we’re looking at today is pretty standard I attempted to get as near to that as I could on uplifts website with similar setups the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus six hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift design is actually 5 inches longer however you can do a lot with 5 inches boom yes now for openness flexi spot did send this desk out for review however as you must understand by now does not impact my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering up until the end of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can possibly get lacking even any cable grommets for travel through the outside container
for the desktop was not damaged in any way which is utterly bizarre because I might shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted simply incredibly rough male if I had acquired this I ‘d have been on the phone with customer service immediately they did likewise handled to miss drilling the pilot holes where you can attach the control box to the desktop a great deal of needing to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact quite straightforward the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each part to support motorized function unusually absolutely where any type of cable management materials whatsoever the frame on this unit is a single motor dual phase design versus the dual motor three-stage style that comes requirement with the uplift desk this can be upgraded too to both the double phase dual motor and a three-stage dual motor which pushes the cost of the desk up
an extra 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to just over forty seven point 6 inches so a max I ‘d it is more than high adequate even for me and I remain at 6 foot for this model does come standard with the control panel that permits up-and-down movement plus three memory spots with an LED readout to inform you the desk height the single motor style uses this drive shaft assembly which needs to be adjusted as the width of the desk is adjusted the motor operation itself while it might be sluggish is really peaceful as in barely audible this outside a rate would be the one benefit I would provide this unit over the uplift desk and I want to take care here since this isn’t a hit piece this desk is 240 dollars less expensive than the comparable uplift design over 35% less expensive even if you update this flexi spot test to the double motor three-stage design it still is available in a hundred and seventy dollars cheaper than the uplift however more affordable does not suggest cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is strong even if max height I’ll absolutely provide it that but the lateral stability of this desk the horizontal movement at this cost point it’s inappropriate it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the sound and this baffle is absolutely frustrating to leading things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters showed up damaged also my prepare for this desk at this moment is to lose the desk top and came with completely and change it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches broad and 31 and a half inches deep so this will roll around the studio make it much easier to film products without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift first that is a financial investment in quality office furniture that will last you this at best seems like a cheaper replica of that it simply does not feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to check out their website too which also feels strangely similar to one of their rivals there’s a wealth of accessories you can get for the flexi area desk as much as and consisting of a foot massager and even a fixed exercise bike and I might spend another 10 minutes of our precious time covering various alternatives and accessories I could however I think I’m happier that they just sent out a standard desk due to the fact that as a standard desk I’m not a fan of the quality assurance at this rate point and I don’t believe slapping on a bunch of extras is the relocation when the core product isn’t what it need to be they do provide a 30-day trial if you’re simply morbidly curious and they warranty their desks for three years extremely desk is five years and uplift desk is seven years if you are Flexispot Mahogany
in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in regards to video gaming and productivity but I would invest the extra money it’s gon na require to enter into a higher end producer like uplift desk or really desk and I have not personally used extremely desk products so I can’t speak on it but their credibility is great big thanks to flexi spot for sending this out for evaluation unfortunately I can not advise this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with viewing as how both the desktop and the casters arrived damaged but from a consumer viewpoint you ‘d most likely be actually excited to get this in