Flexispot Standing Desk Evaluation …Flexispot Instagram…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of functions that I wasn’t necessarily a big fan of:
The plan that the desk can be found in was heavy, so bringing it inside was a group effort, however this is just a consequence of how tough the Flexispot is.
The convenient cable tray was a bit complicated to install. In the end, you eventually slip it under screws, which wasn’t really clear from the instructions.
You will require to buy an anti-fatigue mat to remain comfortable, but this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both excited (given that this suggested it was going to be tough) and also a little reluctant (due to the fact that we all know how much of a challenge putting together furnishings can be).
The good news is, with the help of a training YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I discovered wasn’t discussed well in the directions.
Once put together, I love the smooth appearance of this desk. I’m positive any of the many diverse finishes that it can be found in would look great in any office, and the adjustable width makes it simple to fit it in even the smallest of office.
The quiet operation and height memory settings make it simple, effective, and peaceful to change in between sitting and standing as many times as you desire throughout the day.
Last but not least, this desk is sturdy. It can hold up to 335 pounds even while in operation, so if you have a significant desktop computer (or wish to take a nap on it for some reason) it has you covered. It will also equally disperse weight no matter how unbalanced the weight you place on it is, it will not wiggle or wobble.
in that video is pretty kitted out as the desk we’re looking at today is pretty standard I tried to get as near that as I could on uplifts site with comparable configurations the flexi area desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift model is in fact five inches longer however you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for evaluation but as you need to know by now doesn’t affect my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering till completion of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can possibly get lacking even any cable television grommets for go through the outdoors carton
for the desktop was not harmed in any way which is entirely unusual because I could shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted simply extremely rough male if I had actually purchased this I ‘d have been on the phone with customer support right away they did also handled to miss out on drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without unintentionally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually pretty simple the whole thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each component to support motorized function oddly definitely where any kind of cable television management products whatsoever the frame on this system is a single motor double stage style versus the double motor three-stage design that comes standard with the uplift desk this can be updated also to both the dual stage double motor and a three-stage double motor which presses the cost of the desk up
an additional 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from just under 28 inches to just over forty seven point six inches so a max I ‘d it is more than tall enough even for me and I stay at 6 foot for this design does come basic with the control panel that permits up-and-down motion plus three memory spots with an LED readout to tell you the desk height the single motor design utilizes this drive shaft assembly which has to be adjusted as the width of the desk is adjusted the motor operation itself while it might be slow is very quiet as in barely audible this outside a price would be the one benefit I would give this unit over the uplift desk and I want to be careful here due to the fact that this isn’t a hit piece this desk is 240 dollars cheaper than the similar uplift design over 35% less expensive even if you upgrade this flexi spot test to the dual motor three-stage design it still can be found in a hundred and seventy dollars cheaper than the uplift but more affordable does not mean low-cost this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll absolutely give it that however the lateral stability of this desk the horizontal motion at this price point it’s inappropriate it’s add fuel to the fire here they include a little security baffle this little steel piece that installs to the frame and covers a part of this turning driveshaft when
this desk sees any lateral motion at all the drive shaft strikes this baffle and the noise is absolutely shocking to top things off I decided to add rolling casters to this desk this was a $30 upgrade and two of those 4 casters showed up damaged also my plan for this desk at this point is to lose the desk top and featured completely and change it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches large and 31 and a half inches deep so this will roll around the studio make it much easier to movie items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality workplace furnishings that will last you this at finest feels like a more affordable imitation of that it just does not feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to take a look at their website as well which also feels strangely similar to among their rivals there’s a wealth of accessories you can get for the flexi area desk approximately and consisting of a foot massager and even a stationary exercise bike and I could invest another 10 minutes of our valuable time covering different options and devices I could but I think I’m better that they only sent out a fundamental desk due to the fact that as a standard desk I’m not a fan of the quality control at this cost point and I don’t think slapping on a bunch of bonus is the move when the core product isn’t what it should be they do offer a 30-day trial if you’re just morbidly curious and they service warranty their desks for three years really desk is 5 years and uplift desk is 7 years if you are Flexispot Instagram
in the market for a sit-stand desk they’re amazing mine’s been a life changer for me both in terms of video gaming and productivity however I would spend the extra money it’s gon na take to enter a greater end maker like uplift desk or really desk and I have not personally utilized really desk products so I can’t speak on it however their credibility is excellent huge thanks to flexi area for sending this out for evaluation sadly I can not suggest this unit and for the record I’m a hundred percent sure they would have happily changed the parts that I had a problem with viewing as how both the desktop and the casters showed up harmed however from a customer perspective you ‘d probably be really delighted to get this in