Flexispot Standing Desk Evaluation …Flexispot F7D…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a few features that I wasn’t always a huge fan of:
The package that the desk was available in was heavy, so bringing it inside was a group effort, however this is just a consequence of how durable the Flexispot is.
The convenient cable tray was a little bit complicated to install. In the end, you eventually slip it under screws, which wasn’t really clear from the instructions.
You will need to purchase an anti-fatigue mat to stay comfy, but this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.
When it got here and I saw how heavy it was, I was both excited (considering that this meant it was going to be sturdy) and also a little reluctant (since all of us understand just how much of a difficulty putting together furnishings can be).
The good news is, with the help of an instructional YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old child, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I discovered wasn’t described well in the instructions.
As soon as put together, I enjoy the sleek look of this desk. I’m confident any of the many varied finishes that it is available in would look fantastic in any workplace, and the adjustable width makes it easy to fit it in even the smallest of office.
The peaceful operation and height memory settings make it simple, effective, and peaceful to switch in between sitting and standing as often times as you desire throughout the day.
Last but not least, this desk is strong. It can hold up to 335 lbs even while in operation, so if you have a large desktop (or want to rest on it for some reason) it has you covered. It will also equally disperse weight no matter how unbalanced the weight you place on it is, it won’t wiggle or wobble.
in that video is pretty kitted out as the desk we’re looking at today is pretty fundamental I tried to get as close to that as I might on uplifts website with similar configurations the flexi area desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift model is actually 5 inches longer but you can do a lot with 5 inches boom yes now for openness flexi area did send this desk out for evaluation however as you need to know by now doesn’t impact my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not delivering till the end of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can potentially get lacking even any cable grommets for travel through the outdoors carton
for the desktop was not harmed in any way which is entirely unusual due to the fact that I could shoot a 30-second b-roll montage of just the damage and flaws on this desktop scuffed scraped pitted just very rough man if I had actually acquired this I ‘d have been on the phone with customer service instantly they did likewise managed to miss drilling the pilot holes where you can connect the control box to the desktop a lot of having to do that myself without inadvertently drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was really quite uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each part to support motorized function unusually absolutely where any kind of cable management products whatsoever the frame on this system is a single motor double phase style versus the double motor three-stage style that comes requirement with the uplift desk this can be updated also to both the dual phase double motor and a three-stage double motor which presses the expense of the desk up
an additional 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can vary from simply under 28 inches to simply over forty seven point six inches so a max I ‘d it is more than high adequate even for me and I stay at 6 foot for this design does come standard with the control board that allows for up-and-down motion plus 3 memory spots with an LED readout to tell you the desk height the single motor design uses this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is very peaceful as in barely audible this outside a price would be the one advantage I would offer this system over the uplift desk and I wish to take care here since this isn’t a hit piece this desk is 240 dollars less expensive than the equivalent uplift model over 35% less expensive even if you update this flexi area test to the double motor three-stage design it still can be found in a hundred and seventy dollars cheaper than the uplift but less expensive does not suggest cheap this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll certainly offer it that but the lateral stability of this desk the horizontal motion at this rate point it’s undesirable it’s add insult to injury here they include a little security baffle this little steel piece that mounts to the frame and covers a portion of this turning driveshaft when
this desk sees any lateral movement at all the drive shaft strikes this baffle and the sound is definitely frustrating to leading things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters showed up harmed also my plan for this desk at this moment is to lose the desk top and featured entirely and change it with a white laminate lemon table from Ikea and use it as an adjustable image table which you can’t do this frame will accommodate desktops up to 63 inches large and 31 and a half inches deep so this will roll around the studio make it easier to film products without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is an investment in quality office furniture that will last you this at finest seems like a less expensive imitation of that it simply doesn’t feel quality and the difference in between this desk and my main desk is night and day do do not hesitate to have a look at their site as well which likewise feels strangely similar to among their competitors there’s a wealth of accessories you can get for the flexi area desk approximately and consisting of a foot massager and even a fixed stationary bicycle and I might invest another 10 minutes of our valuable time covering different options and accessories I might but I think I’m better that they just sent a fundamental desk due to the fact that as a fundamental desk I’m not a fan of the quality assurance at this cost point and I do not believe slapping on a bunch of bonus is the relocation when the core item isn’t what it must be they do provide a 30-day trial if you’re simply morbidly curious and they warranty their desks for 3 years really desk is five years and uplift desk is 7 years if you are Flexispot F7D
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and performance however I would spend the extra money it’s gon na take to enter a higher end producer like uplift desk or really desk and I have not personally utilized very desk items so I can’t speak on it but their reputation is excellent big thanks to flexi spot for sending this out for evaluation regrettably I can not suggest this unit and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had an issue with seeing as how both the desktop and the casters showed up damaged however from a client standpoint you ‘d most likely be actually thrilled to get this in