Flexispot E7 Vs E8 – 77% OFF Today Only

Flexispot Standing Desk Review …Flexispot E7 Vs E8…

Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of features that I wasn’t always a substantial fan of:

The bundle that the desk came in was heavy, so bringing it inside was a group effort, however this is simply a consequence of how strong the Flexispot is.
The hassle-free cable tray was a bit complicated to install. In the end, you ultimately slip it under screws, which wasn’t very clear from the instructions.
You will need to buy an anti-fatigue mat to stay comfy, but this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.

When it arrived and I saw how heavy it was, I was both thrilled (given that this implied it was going to be durable) and likewise a little reluctant (since we all understand how much of an obstacle assembling furniture can be).

The good news is, with the help of a training YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t discussed well in the instructions.

As soon as assembled, I like the streamlined look of this desk. I’m confident any of the many diverse finishes that it comes in would look fantastic in any office, and the adjustable width makes it simple to fit it in even the tiniest of home offices.

The quiet operation and height memory settings make it easy, effective, and peaceful to switch between sitting and standing as often times as you want throughout the day.

This desk is sturdy. It can hold up to 335 lbs even while in operation, so if you have a large desktop computer (or wish to rest on it for some reason) it has you covered. It will likewise uniformly distribute weight no matter how out of balance the weight you put on it is, it will not wiggle or wobble.

 

in that video is quite kitted out as the desk we’re looking at today is pretty basic I attempted to get as close to that as I might on uplifts website with equivalent configurations the flexi area desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a comparable desk from uplift I attempt to get as close as possible with the uplift design is really five inches longer however you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for evaluation however as you must understand by now doesn’t impact my evaluation in any way the desktop here is 55 inches wide 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping up until completion of April at the earliest the desktop is an inch thick but it’s this fundamental laminate as you can perhaps get doing not have even any cable television grommets for go through the outside carton

for the desktop was not harmed in any way which is utterly unusual due to the fact that I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted just super rough male if I had purchased this I ‘d have been on the phone with customer care immediately they did also managed to miss out on drilling the pilot holes where you can connect the control box to the desktop a great deal of needing to do that myself without inadvertently drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact quite simple the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function strangely absolutely where any kind of cable management materials whatsoever the frame on this system is a single motor double stage design versus the dual motor three-stage style that comes requirement with the uplift desk this can be upgraded too to both the double phase dual motor and a three-stage dual motor which pushes the cost of the desk up

an extra 70 dollars the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to simply over forty seven point six inches so a max I ‘d it is more than tall sufficient even for me and I remain at 6 foot for this model does come standard with the control board that enables up-and-down motion plus three memory spots with an LED readout to inform you the desk height the single motor design utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be sluggish is very quiet as in barely audible this outside a cost would be the one benefit I would give this system over the uplift desk and I wish to beware here since this isn’t a hit piece this desk is 240 dollars more affordable than the comparable uplift model over 35% cheaper even if you upgrade this flexi spot test to the dual motor three-stage design it still can be found in a hundred and seventy dollars less expensive than the uplift but less expensive doesn’t indicate inexpensive this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll definitely give it that but the lateral stability of this desk the horizontal motion at this price point it’s undesirable it’s rub salt in the wound here they include a little safety baffle this little steel piece that installs to the frame and covers a portion of this turning driveshaft when

this desk sees any lateral motion at all the drive shaft hits the sound and this baffle is definitely frustrating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and two of those four casters showed up damaged also my plan for this desk at this point is to lose the desk top and featured all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops up to 63 inches broad and 31 and a half inches deep so this will roll around the studio make it simpler to film items without needing to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furniture that will last you this at finest seems like a more affordable imitation of that it simply does not feel quality and the difference in between this desk and my primary desk is night and day do do not hesitate to check out their website also which likewise feels eerily comparable to one of their rivals there’s a wealth of accessories you can get for the flexi spot desk as much as and including a foot massager and even a fixed exercise bike and I could spend another 10 minutes of our precious time covering various alternatives and accessories I might but I think I’m better that they only sent out a standard desk since as a basic desk I’m not a fan of the quality assurance at this price point and I do not think slapping on a bunch of extras is the move when the core product isn’t what it should be they do use a 30-day trial if you’re just morbidly curious and they warranty their desks for 3 years really desk is 5 years and uplift desk is 7 years if you are Flexispot E7 Vs E8

in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in terms of gaming and performance however I would invest the extra money it’s gon na take to get into a greater end maker like uplift desk or really desk and I haven’t personally utilized extremely desk items so I can’t speak on it but their credibility is great big thanks to flexi area for sending this out for review sadly I can not suggest this system and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with seeing as how both the desktop and the casters arrived harmed however from a customer standpoint you ‘d probably be really delighted to get this in