Flexispot E7 Pro E8 – 77% OFF Today Only

Flexispot Standing Desk Evaluation …Flexispot E7 Pro E8…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are very little, here are a couple of features that I wasn’t necessarily a huge fan of:

The package that the desk came in was heavy, so bringing it inside was a group effort, however this is just a consequence of how sturdy the Flexispot is.
The convenient cable television tray was a bit complicated to set up. In the end, you ultimately slip it under screws, which wasn’t very clear from the guidelines.
You will need to buy an anti-fatigue mat to remain comfy, but this is a good concept for any standing desks, so I can’t fault Flexispot for that.

When it arrived and I saw how heavy it was, I was both excited (given that this indicated it was going to be durable) and also a little hesitant (because we all know just how much of an obstacle assembling furniture can be).

Fortunately, with the help of a training YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t discussed well in the directions.

When put together, I like the streamlined look of this desk. I’m confident any of the many diverse surfaces that it can be found in would look fantastic in any workplace, and the adjustable width makes it easy to fit it in even the smallest of office.

The quiet operation and height memory settings make it easy, effective, and quiet to switch in between sitting and standing as many times as you desire throughout the day.

This desk is strong. It can hold up to 335 lbs even while in operation, so if you have a large desktop (or want to take a nap on it for some reason) it has you covered. It will also uniformly disperse weight no matter how out of balance the weight you place on it is, it will not wiggle or wobble.

 

because video is quite kitted out as the desk we’re looking at today is quite fundamental I attempted to get as close to that as I could on uplifts website with equivalent configurations the flexi area desk we’re taking a look at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift model is in fact five inches longer but you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for evaluation however as you should understand by now does not impact my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping until the end of April at the earliest the desktop is an inch thick however it’s this basic laminate as you can possibly get doing not have even any cable television grommets for travel through the outside container

for the desktop was not harmed in any way which is entirely unusual since I could shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted just incredibly rough male if I had actually purchased this I ‘d have been on the phone with customer support immediately they did also managed to miss drilling the pilot holes where you can attach the control box to the desktop a great deal of needing to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact quite simple the entire thing came together in about 45 minutes and despite the fact that there’s cable televisions going to it from each component to support motorized function oddly definitely where any kind of cable television management materials whatsoever the frame on this unit is a single motor dual stage design versus the double motor three-stage design that comes requirement with the uplift desk this can be updated also to both the dual stage dual motor and a three-stage double motor which pushes the expense of the desk up

an extra 70 dollars the frame is designed for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from simply under 28 inches to simply over forty 7 point 6 inches so a max I ‘d it is more than high enough even for me and I stay at 6 foot for this model does come standard with the control board that permits up-and-down motion plus three memory spots with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be sluggish is really peaceful as in barely audible this outside a cost would be the one benefit I would offer this unit over the uplift desk and I wish to beware here since this isn’t a hit piece this desk is 240 dollars cheaper than the equivalent uplift model over 35% cheaper even if you update this flexi spot test to the double motor three-stage style it still can be found in a hundred and seventy dollars more affordable than the uplift however more affordable does not imply cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll definitely give it that but the lateral stability of this desk the horizontal motion at this rate point it’s unacceptable it’s add insult to injury here they consist of a little security baffle this little steel piece that installs to the frame and covers a portion of this rotating driveshaft when

this desk sees any lateral movement at all the drive shaft hits this baffle and the sound is absolutely shocking to top things off I chose to add rolling casters to this desk this was a $30 upgrade and two of those 4 casters got here harmed also my plan for this desk at this moment is to lose the desk top and featured all together and change it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops as much as 63 inches broad and 31 and a half inches deep so this will roll around the studio make it much easier to film items without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift first that is an investment in quality office furniture that will last you this at best seems like a less expensive imitation of that it just does not feel quality and the distinction between this desk and my main desk is night and day do feel free to take a look at their site too which likewise feels strangely similar to one of their competitors there’s a wealth of devices you can get for the flexi area desk up to and including a foot massager and even a fixed stationary bicycle and I might invest another 10 minutes of our precious time covering numerous choices and devices I could however I believe I’m better that they just sent out a fundamental desk due to the fact that as a fundamental desk I’m not a fan of the quality control at this cost point and I do not believe slapping on a bunch of additionals is the relocation when the core product isn’t what it should be they do offer a 30-day trial if you’re just morbidly curious and they warranty their desks for 3 years extremely desk is 5 years and uplift desk is 7 years if you are Flexispot E7 Pro E8

in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in terms of video gaming and performance however I would invest the additional money it’s gon na require to get into a greater end manufacturer like uplift desk or really desk and I have not personally used extremely desk items so I can’t speak on it but their credibility is excellent big thanks to flexi spot for sending this out for evaluation sadly I can not advise this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had a problem with viewing as how both the desktop and the casters got here damaged but from a client perspective you ‘d most likely be really delighted to get this in