Flexispot E7 E8 – 77% OFF Today Only

Flexispot Standing Desk Evaluation …Flexispot E7 E8…

Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of functions that I wasn’t necessarily a big fan of:

The bundle that the desk came in was heavy, so bringing it inside was a group effort, but this is just a consequence of how tough the Flexispot is.
The hassle-free cable tray was a bit complicated to install. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the instructions.
You will require to purchase an anti-fatigue mat to stay comfy, but this is a good idea for any standing desks, so I can’t fault Flexispot for that.

When it arrived and I saw how heavy it was, I was both fired up (because this suggested it was going to be durable) and likewise a little hesitant (since all of us know how much of a challenge putting together furnishings can be).

Luckily, with the help of an instructional YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t discussed well in the instructions.

As soon as put together, I love the streamlined appearance of this desk. I’m positive any of the many varied surfaces that it can be found in would look fantastic in any workplace, and the adjustable width makes it simple to fit it in even the tiniest of home offices.

The quiet operation and height memory settings make it simple, effective, and peaceful to change in between sitting and standing as lot of times as you want throughout the day.

Finally, this desk is tough. It can hold up to 335 pounds even while in operation, so if you have a significant desktop (or wish to sleep on it for some reason) it has you covered. It will also evenly distribute weight no matter how unbalanced the weight you place on it is, it will not wobble or wiggle.

 

in that video is pretty kitted out as the desk we’re looking at today is pretty basic I attempted to get as close to that as I could on uplifts site with comparable setups the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift model is in fact 5 inches longer however you can do a lot with 5 inches boom yes now for openness flexi spot did send this desk out for evaluation but as you ought to know by now doesn’t affect my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping up until the end of April at the earliest the desktop is an inch thick however it’s this basic laminate as you can perhaps get doing not have even any cable television grommets for travel through the outdoors container

for the desktop was not damaged in any way which is utterly bizarre since I might shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted simply extremely rough man if I had acquired this I ‘d have been on the phone with customer support instantly they did likewise handled to miss drilling the pilot holes where you can connect the control box to the desktop a lot of needing to do that myself without unintentionally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact pretty simple the whole thing came together in about 45 minutes and despite the fact that there’s cable televisions running to it from each part to support motorized function strangely absolutely where any type of cable television management materials whatsoever the frame on this unit is a single motor double phase design versus the dual motor three-stage design that comes standard with the uplift desk this can be upgraded as well to both the double phase dual motor and a three-stage dual motor which pushes the cost of the desk up

an additional 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from just under 28 inches to just over forty seven point 6 inches so a max I ‘d it is more than tall enough even for me and I remain at 6 foot for this design does come basic with the control panel that allows for up-and-down movement plus three memory areas with an LED readout to tell you the desk height the single motor design uses this drive shaft assembly which has to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is really quiet as in barely audible this outside a cost would be the one advantage I would provide this unit over the uplift desk and I wish to be careful here since this isn’t a hit piece this desk is 240 dollars cheaper than the comparable uplift model over 35% more affordable even if you update this flexi spot test to the dual motor three-stage style it still can be found in a hundred and seventy dollars cheaper than the uplift but less expensive doesn’t suggest inexpensive this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll definitely offer it that but the lateral stability of this desk the horizontal movement at this rate point it’s inappropriate it’s add insult to injury here they consist of a little security baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when

this desk sees any lateral motion at all the drive shaft strikes this baffle and the sound is absolutely shocking to leading things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters arrived harmed as well my prepare for this desk at this point is to lose the desk top and came with completely and replace it with a white laminate lemon table from Ikea and use it as an adjustable picture table which you can’t do this frame will accommodate desktops up to 63 inches large and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furniture that will last you this at finest seems like a more affordable replica of that it simply doesn’t feel quality and the distinction between this desk and my primary desk is night and day do do not hesitate to take a look at their website as well which also feels eerily similar to one of their competitors there’s a wealth of accessories you can get for the flexi spot desk approximately and including a foot massager and even a fixed stationary bicycle and I might invest another 10 minutes of our valuable time covering numerous options and accessories I could but I believe I’m better that they only sent out a fundamental desk because as a basic desk I’m not a fan of the quality control at this price point and I don’t think slapping on a lot of extras is the move when the core product isn’t what it must be they do use a 30-day trial if you’re simply morbidly curious and they warranty their desks for 3 years extremely desk is five years and uplift desk is seven years if you are Flexispot E7 E8

in the market for a sit-stand desk they’re fantastic mine’s been a life changer for me both in terms of video gaming and performance but I would invest the money it’s gon na take to get into a greater end manufacturer like uplift desk or really desk and I have not personally utilized very desk products so I can’t speak on it however their track record is very good huge thanks to flexi spot for sending this out for evaluation unfortunately I can not recommend this system and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a concern with viewing as how both the desktop and the casters showed up harmed but from a client viewpoint you ‘d probably be truly thrilled to get this in