Flexispot Standing Desk Evaluation …Flexispot Desk Missing Holes…
Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a couple of functions that I wasn’t necessarily a big fan of:
The plan that the desk was available in was heavy, so bringing it inside was a group effort, but this is simply an effect of how strong the Flexispot is.
The practical cable television tray was a little bit confusing to install. In the end, you eventually slip it under screws, which wasn’t very clear from the directions.
You will require to purchase an anti-fatigue mat to remain comfortable, but this is an excellent idea for any standing desks, so I can’t fault Flexispot for that.
When it showed up and I saw how heavy it was, I was both fired up (considering that this suggested it was going to be sturdy) and likewise a little hesitant (since we all know just how much of a challenge assembling furnishings can be).
The good news is, with the help of an educational YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only problem I have with assembly was the cable tray, which I discovered wasn’t discussed well in the guidelines.
Once put together, I like the smooth look of this desk. I’m confident any of the many diverse surfaces that it can be found in would look terrific in any office, and the adjustable width makes it simple to fit it in even the tiniest of office.
The peaceful operation and height memory settings make it simple, efficient, and quiet to change between sitting and standing as lot of times as you want throughout the day.
Finally, this desk is strong. It can hold up to 335 lbs even while in operation, so if you have a large desktop computer (or want to take a nap on it for some reason) it has you covered. It will likewise equally disperse weight no matter how out of balance the weight you place on it is, it will not wobble or wiggle.
because video is quite kitted out as the desk we’re looking at today is quite basic I tried to get as near that as I might on uplifts website with equivalent configurations the flexi spot desk we’re looking at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a similar desk from uplift I try to get as close as possible with the uplift design is in fact 5 inches longer but you can do a lot with five inches boom yes now for openness flexi spot did send this desk out for review however as you need to understand by now does not impact my review in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not shipping until completion of April at the earliest the desktop is an inch thick but it’s this standard laminate as you can potentially get doing not have even any cable grommets for travel through the outdoors carton
for the desktop was not damaged in any way which is absolutely bizarre because I might shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply extremely rough man if I had actually bought this I ‘d have been on the phone with customer support instantly they did likewise managed to miss drilling the pilot holes where you can attach the control box to the desktop a great deal of having to do that myself without accidentally drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each component to support motorized function strangely absolutely where any type of cable management products whatsoever the frame on this system is a single motor double stage design versus the double motor three-stage style that comes requirement with the uplift desk this can be updated also to both the double stage dual motor and a three-stage dual motor which pushes the cost of the desk up
an additional 70 bucks the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can vary from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than tall sufficient even for me and I remain at 6 foot for this design does come basic with the control panel that permits up-and-down motion plus three memory areas with an LED readout to tell you the desk height the single motor style utilizes this drive shaft assembly which needs to be adjusted as the width of the desk is changed the motor operation itself while it might be slow is extremely quiet as in barely audible this outside a cost would be the one benefit I would give this system over the uplift desk and I want to be careful here since this isn’t a hit piece this desk is 240 dollars more affordable than the similar uplift model over 35% less expensive even if you update this flexi spot test to the dual motor three-stage style it still is available in a hundred and seventy dollars cheaper than the uplift however less expensive doesn’t indicate cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll definitely provide it that but the lateral stability of this desk the horizontal movement at this price point it’s unacceptable it’s add insult to injury here they include a little safety baffle this little steel piece that mounts to the frame and covers a portion of this rotating driveshaft when
this desk sees any lateral motion at all the drive shaft hits this baffle and the sound is absolutely frustrating to top things off I decided to include rolling casters to this desk this was a $30 upgrade and two of those four casters arrived damaged as well my prepare for this desk at this point is to lose the desk top and came with completely and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops as much as 63 inches broad and 31 and a half inches deep so this will roll around the studio make it easier to film products without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality office furniture that will last you this at finest seems like a cheaper replica of that it simply doesn’t feel quality and the difference in between this desk and my main desk is night and day do feel free to take a look at their website as well which also feels strangely similar to one of their competitors there’s a wealth of accessories you can get for the flexi spot desk up to and including a foot massager and even a stationary exercise bike and I could spend another 10 minutes of our valuable time covering numerous options and devices I could however I believe I’m happier that they just sent out a standard desk because as a standard desk I’m not a fan of the quality control at this price point and I don’t believe slapping on a lot of extras is the move when the core item isn’t what it need to be they do offer a 30-day trial if you’re just morbidly curious and they guarantee their desks for three years really desk is five years and uplift desk is seven years if you are Flexispot Desk Missing Holes
in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in regards to gaming and productivity however I would spend the extra money it’s gon na require to enter a higher end maker like uplift desk or really desk and I haven’t personally utilized extremely desk products so I can’t speak on it but their reputation is excellent big thanks to flexi area for sending this out for evaluation unfortunately I can not recommend this unit and for the record I’m a hundred percent sure they would have happily replaced the parts that I had a problem with viewing as how both the desktop and the casters got here harmed but from a customer viewpoint you ‘d most likely be actually excited to get this in