Flexispot Customer Service – 77% OFF Today Only

Flexispot Standing Desk Review …Flexispot Customer Service…

Cons: What I Didn’t Like About the Flexispot E7
The cons on this desk are minimal, here are a few features that I wasn’t always a huge fan of:

The bundle that the desk can be found in was heavy, so bringing it inside was a group effort, however this is just a repercussion of how sturdy the Flexispot is.
The practical cable tray was a bit complicated to set up. In the end, you eventually slip it under screws, which wasn’t extremely clear from the guidelines.
You will need to purchase an anti-fatigue mat to stay comfy, but this is an excellent concept for any standing desks, so I can’t fault Flexispot for that.

When it showed up and I saw how heavy it was, I was both fired up (since this meant it was going to be tough) and likewise a little reluctant (due to the fact that we all know how much of a challenge putting together furnishings can be).

Fortunately, with the help of an instructional YouTube link, it took me just around 42 minutes to put together. Scratch that, it took my 11-year-old daughter, with some supervision from me, from start to finish. The only hang-up I have with assembly was the cable tray, which I discovered wasn’t explained well in the directions.

Once put together, I like the streamlined look of this desk. I’m confident any of the many varied surfaces that it can be found in would look terrific in any office, and the adjustable width makes it easy to fit it in even the smallest of home offices.

The quiet operation and height memory settings make it simple, efficient, and peaceful to switch in between sitting and standing as lot of times as you desire throughout the day.

This desk is strong. It can hold up to 335 pounds even while in operation, so if you have a large desktop (or want to rest on it for some reason) it has you covered. It will likewise equally distribute weight no matter how unbalanced the weight you put on it is, it won’t wiggle or wobble.

 

because video is pretty kitted out as the desk we’re taking a look at today is pretty basic I attempted to get as near that as I might on uplifts site with similar configurations the flexi spot desk we’re looking at today will run you about four hundred and ten dollars versus 6 hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is in fact five inches longer but you can do a lot with five inches boom yes now for transparency flexi area did send this desk out for evaluation however as you should understand by now doesn’t affect my review in any way the desktop here is 55 inches large 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering until completion of April at the earliest the desktop is an inch thick however it’s this basic laminate as you can possibly get lacking even any cable television grommets for pass through the outside carton

for the desktop was not damaged in any way which is utterly bizarre since I could shoot a 30-second b-roll montage of just the damage and defects on this desktop scuffed scraped pitted simply incredibly rough guy if I had actually bought this I ‘d have been on the phone with customer care right away they did likewise managed to miss drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without mistakenly drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface area to the frame that’s a far cry from the embedded metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was actually pretty uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each part to support motorized function strangely absolutely where any type of cable management products whatsoever the frame on this system is a single motor double phase design versus the dual motor three-stage design that comes standard with the uplift desk this can be upgraded too to both the double phase dual motor and a three-stage dual motor which presses the cost of the desk up

an additional 70 bucks the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from simply under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than high adequate even for me and I stay at 6 foot for this design does come basic with the control board that enables up-and-down motion plus 3 memory spots with an LED readout to tell you the desk height the single motor design uses this drive shaft assembly which needs to be changed as the width of the desk is changed the motor operation itself while it might be sluggish is really peaceful as in barely audible this outside a price would be the one advantage I would provide this unit over the uplift desk and I wish to take care here because this isn’t a hit piece this desk is 240 dollars cheaper than the equivalent uplift model over 35% more affordable even if you update this flexi spot test to the dual motor three-stage design it still comes in a hundred and seventy dollars less expensive than the uplift however less expensive does not indicate low-cost this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll absolutely give it that but the lateral stability of this desk the horizontal motion at this rate point it’s inappropriate it’s add insult to injury here they include a little safety baffle this little steel piece that installs to the frame and covers a portion of this turning driveshaft when

this desk sees any lateral movement at all the drive shaft hits this baffle and the sound is absolutely shocking to top things off I decided to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters arrived damaged too my prepare for this desk at this point is to lose the desk top and came with all together and replace it with a white laminate lemon table from Ikea and utilize it as an adjustable photo table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it much easier to film items without needing to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I discovered uplift initially that is a financial investment in quality workplace furniture that will last you this at best feels like a less expensive imitation of that it simply doesn’t feel quality and the distinction between this desk and my main desk is night and day do do not hesitate to have a look at their site too which likewise feels eerily comparable to among their rivals there’s a wealth of accessories you can get for the flexi area desk up to and including a foot massager and even a stationary stationary bicycle and I might spend another 10 minutes of our valuable time covering different options and devices I might however I believe I’m happier that they only sent a fundamental desk since as a basic desk I’m not a fan of the quality assurance at this cost point and I do not think slapping on a lot of additionals is the relocation when the core item isn’t what it must be they do offer a 30-day trial if you’re simply morbidly curious and they service warranty their desks for three years very desk is 5 years and uplift desk is 7 years if you are Flexispot Customer Service

in the market for a sit-stand desk they’re remarkable mine’s been a life changer for me both in regards to video gaming and performance however I would spend the extra money it’s gon na take to get into a higher end maker like uplift desk or really desk and I have not personally utilized really desk products so I can’t speak on it but their track record is excellent huge thanks to flexi area for sending this out for evaluation unfortunately I can not recommend this unit and for the record I’m a hundred percent sure they would have gladly changed the parts that I had an issue with viewing as how both the desktop and the casters got here harmed but from a customer viewpoint you ‘d most likely be actually delighted to get this in