Flexispot Standing Desk Review …Flexispot Customer Service Reviews…
Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a few features that I wasn’t always a huge fan of:
The package that the desk came in was heavy, so bringing it inside was a group effort, but this is simply an effect of how tough the Flexispot is.
The practical cable tray was a little bit complicated to install. In the end, you eventually slip it under screws, which wasn’t extremely clear from the guidelines.
You will require to purchase an anti-fatigue mat to remain comfortable, however this is a great idea for any standing desks, so I can’t fault Flexispot for that.
When it arrived and I saw how heavy it was, I was both thrilled (because this suggested it was going to be sturdy) and also a little hesitant (due to the fact that we all understand how much of a challenge assembling furniture can be).
Thankfully, with the help of an educational YouTube link, it took me just around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only hang-up I have with assembly was the cable television tray, which I found wasn’t discussed well in the directions.
As soon as assembled, I like the sleek look of this desk. I’m positive any of the many diverse surfaces that it can be found in would look great in any workplace, and the adjustable width makes it simple to fit it in even the smallest of office.
The peaceful operation and height memory settings make it easy, effective, and peaceful to switch between sitting and standing as often times as you want throughout the day.
Finally, this desk is tough. It can hold up to 335 pounds even while in operation, so if you have a significant desktop (or want to sleep on it for some reason) it has you covered. It will likewise evenly distribute weight no matter how out of balance the weight you place on it is, it will not wobble or wiggle.
in that video is pretty kitted out as the desk we’re looking at today is pretty standard I attempted to get as close to that as I might on uplifts website with similar configurations the flexi area desk we’re looking at today will run you about four hundred and ten dollars versus six hundred and fifty for a similar desk from uplift I attempt to get as close as possible with the uplift design is in fact 5 inches longer but you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for review however as you should know by now doesn’t impact my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming but it’s not delivering up until completion of April at the earliest the desktop is an inch thick but it’s this basic laminate as you can potentially get lacking even any cable grommets for pass through the outside carton
for the desktop was not damaged in any way which is entirely bizarre due to the fact that I might shoot a 30-second b-roll montage of simply the damage and flaws on this desktop scuffed scraped pitted simply extremely rough guy if I had actually bought this I ‘d have been on the phone with client service instantly they did also handled to miss drilling the pilot holes where you can attach the control box to the desktop a lot of needing to do that myself without accidentally drilling through the opposite of the desktop so yeah pilot holes in wood screws is how you’re gon na be attaching the surface area to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from needing to drill that top was really pretty straightforward the entire thing came together in about 45 minutes and despite the fact that there’s cables running to it from each part to support motorized function oddly absolutely where any sort of cable management products whatsoever the frame on this unit is a single motor dual phase design versus the dual motor three-stage style that comes standard with the uplift desk this can be updated also to both the double phase double motor and a three-stage double motor which pushes the cost of the desk up
an extra 70 dollars the frame is developed for a max load of 154 pounds and it moves at a rate at an inch per 2nd the height can range from just under 28 inches to just over forty 7 point six inches so a max I ‘d it is more than tall enough even for me and I stay at 6 foot for this model does come basic with the control board that allows for up-and-down movement plus three memory spots with an LED readout to inform you the desk height the single motor design utilizes this drive shaft assembly which needs to be changed as the width of the desk is adjusted the motor operation itself while it might be slow is really peaceful as in barely audible this outside a price would be the one advantage I would give this system over the uplift desk and I want to take care here because this isn’t a hit piece this desk is 240 dollars less expensive than the similar uplift model over 35% less expensive even if you update this flexi area test to the double motor three-stage design it still can be found in a hundred and seventy dollars more affordable than the uplift however more affordable doesn’t mean cheap this desk is still over four hundred dollars if I had paid over $400 for this desk I ‘d have an issue with that the front to back stability of this desk is solid even if max height I’ll absolutely give it that however the lateral stability of this desk the horizontal motion at this rate point it’s undesirable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that installs to the frame and covers a part of this rotating driveshaft when
this desk sees any lateral movement at all the drive shaft strikes the noise and this baffle is absolutely frustrating to top things off I decided to add rolling casters to this desk this was a $30 upgrade and 2 of those four casters got here damaged also my prepare for this desk at this point is to lose the desk top and included all together and replace it with a white laminate lemon table from Ikea and use it as an adjustable image table which you can’t do this frame will accommodate desktops up to 63 inches large and 31 and a half inches deep so this will roll around the studio make it easier to film products without having to change complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is a financial investment in quality office furnishings that will last you this at best feels like a less expensive imitation of that it simply doesn’t feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to check out their site also which also feels strangely similar to one of their rivals there’s a wealth of accessories you can get for the flexi area desk as much as and consisting of a foot massager and even a stationary stationary bicycle and I might invest another 10 minutes of our precious time covering numerous choices and devices I could but I think I’m better that they only sent out a fundamental desk since as a standard desk I’m not a fan of the quality assurance at this cost point and I don’t believe slapping on a lot of additionals is the move when the core item isn’t what it should be they do offer a 30-day trial if you’re just morbidly curious and they service warranty their desks for 3 years really desk is 5 years and uplift desk is 7 years if you are Flexispot Customer Service Reviews
in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and productivity but I would invest the extra money it’s gon na take to get into a higher end manufacturer like uplift desk or extremely desk and I haven’t personally used very desk items so I can’t speak on it however their credibility is excellent big thanks to flexi spot for sending this out for review sadly I can not suggest this system and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a concern with viewing as how both the desktop and the casters showed up damaged however from a consumer perspective you ‘d most likely be actually delighted to get this in