Flexispot Accessories – 77% OFF Today Only

Flexispot Standing Desk Evaluation …Flexispot Accessories…

Cons: What I Didn’t Like About the Flexispot E7
Though the cons on this desk are minimal, here are a few functions that I wasn’t necessarily a huge fan of:

The package that the desk can be found in was heavy, so bringing it inside was a group effort, but this is simply a repercussion of how strong the Flexispot is.
The convenient cable tray was a little bit confusing to set up. In the end, you ultimately slip it under screws, which wasn’t extremely clear from the instructions.
You will need to purchase an anti-fatigue mat to remain comfy, but this is a good idea for any standing desks, so I can’t fault Flexispot for that.

When it showed up and I saw how heavy it was, I was both fired up (because this indicated it was going to be durable) and also a little hesitant (due to the fact that we all know just how much of a challenge putting together furniture can be).

Luckily, with the help of a training YouTube link, it took me only around 42 minutes to assemble. Scratch that, it took my 11-year-old daughter, with some guidance from me, from start to finish. The only problem I have with assembly was the cable tray, which I found wasn’t discussed well in the instructions.

Once put together, I like the smooth look of this desk. I’m positive any of the many varied finishes that it comes in would look terrific in any workplace, and the adjustable width makes it easy to fit it in even the tiniest of office.

The peaceful operation and height memory settings make it easy, effective, and quiet to change in between sitting and standing as many times as you desire throughout the day.

This desk is strong. It can hold up to 335 lbs even while in operation, so if you have a substantial desktop (or want to rest on it for some reason) it has you covered. It will likewise uniformly disperse weight no matter how out of balance the weight you put on it is, it won’t wobble or wiggle.

 

in that video is quite kitted out as the desk we’re taking a look at today is pretty basic I attempted to get as near to that as I could on uplifts website with comparable setups the flexi area desk we’re taking a look at today will run you about four hundred and 10 dollars versus 6 hundred and fifty for a comparable desk from uplift I try to get as close as possible with the uplift model is in fact 5 inches longer however you can do a lot with 5 inches boom yes now for transparency flexi area did send this desk out for review however as you should know by now doesn’t impact my evaluation in any way the desktop here is 55 inches broad 28 inches deep and comes as a $40 upgrade from the base size of 48 by thirty sixty by thirty is coming however it’s not shipping till completion of April at the earliest the desktop is an inch thick however it’s this fundamental laminate as you can possibly get lacking even any cable television grommets for go through the outside carton

for the desktop was not harmed in any way which is utterly bizarre because I could shoot a 30-second b-roll montage of simply the damage and defects on this desktop scuffed scraped pitted simply very rough male if I had acquired this I ‘d have been on the phone with client service right away they did also managed to miss drilling the pilot holes where you can connect the control box to the desktop a great deal of having to do that myself without mistakenly drilling through the other side of the desktop so yeah pilot holes in wood screws is how you’re gon na be connecting the surface to the frame that’s a far cry from the ingrained metal inserts that we saw on the uplift desk so assembly aside from having to drill that top was in fact quite uncomplicated the entire thing came together in about 45 minutes and despite the fact that there’s cables going to it from each element to support motorized function strangely absolutely where any kind of cable television management materials whatsoever the frame on this system is a single motor double phase style versus the dual motor three-stage design that comes requirement with the uplift desk this can be upgraded as well to both the double phase dual motor and a three-stage dual motor which pushes the expense of the desk up

an additional 70 bucks the frame is created for a max load of 154 pounds and it moves at a rate at an inch per second the height can range from just under 28 inches to simply over forty seven point six inches so a max I ‘d it is more than high adequate even for me and I stay at 6 foot for this design does come standard with the control panel that allows for up-and-down motion plus 3 memory spots with an LED readout to tell you the desk height the single motor style uses this drive shaft assembly which has to be changed as the width of the desk is changed the motor operation itself while it might be slow is very peaceful as in barely audible this outside a cost would be the one benefit I would give this unit over the uplift desk and I wish to take care here since this isn’t a hit piece this desk is 240 dollars less expensive than the equivalent uplift model over 35% less expensive even if you update this flexi area test to the dual motor three-stage design it still can be found in a hundred and seventy dollars less expensive than the uplift but less expensive does not suggest inexpensive this desk is still over four hundred dollars if I had actually paid over $400 for this desk I ‘d have a problem with that the front to back stability of this desk is solid even if max height I’ll absolutely give it that however the lateral stability of this desk the horizontal movement at this price point it’s undesirable it’s add fuel to the fire here they consist of a little safety baffle this little steel piece that mounts to the frame and covers a portion of this turning driveshaft when

this desk sees any lateral movement at all the drive shaft strikes the sound and this baffle is definitely infuriating to top things off I chose to add rolling casters to this desk this was a $30 upgrade and 2 of those 4 casters showed up damaged as well my plan for this desk at this moment is to lose the desk top and came with all together and change it with a white laminate lemon table from Ikea and utilize it as an adjustable picture table which you can’t do this frame will accommodate desktops approximately 63 inches wide and 31 and a half inches deep so this will roll around the studio make it simpler to movie items without having to adjust complex or heavy slider setups and what I personally pay $400 for that no I lucked out that I found uplift initially that is an investment in quality workplace furnishings that will last you this at best seems like a less expensive imitation of that it just does not feel quality and the difference between this desk and my primary desk is night and day do do not hesitate to have a look at their website too which also feels eerily comparable to one of their rivals there’s a wealth of devices you can get for the flexi spot desk as much as and including a foot massager and even a fixed stationary bicycle and I could invest another 10 minutes of our valuable time covering different options and devices I could however I think I’m better that they just sent out a standard desk because as a fundamental desk I’m not a fan of the quality assurance at this price point and I do not think slapping on a bunch of additionals is the move when the core product isn’t what it ought to be they do use a 30-day trial if you’re simply morbidly curious and they service warranty their desks for three years really desk is five years and uplift desk is 7 years if you are Flexispot Accessories

in the market for a sit-stand desk they’re incredible mine’s been a life changer for me both in terms of gaming and performance but I would spend the money it’s gon na take to enter a higher end manufacturer like uplift desk or very desk and I have not personally utilized really desk products so I can’t speak on it but their credibility is very good huge thanks to flexi area for sending this out for review sadly I can not recommend this system and for the record I’m a hundred percent sure they would have gladly replaced the parts that I had a concern with viewing as how both the desktop and the casters showed up damaged however from a client perspective you ‘d probably be truly delighted to get this in